Nov 18th, 2024 at 5:43am (UTC)
 
 

Before logging an issue, please update to the latest release of Visual Micro from the Downloads Page.

When Logging a Support Issue in the Forum, please ensure you have also:-

  • Enabled vMicro > Compiler > Show Build Properties
  • Re-Compile your program with these settings enabled
  		Save the new Output to a Text File and....
  • Click the Reply button and attach as .txt file OR
  • Click here to Email us with the file attached, and a link to your post
Support requests without the output above may be impossible to answer, so please help us to help you
 
  VS Arduino › Visual Micro › General Board › Code completion and itellisense
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Code completion and itellisense (Read 5043 times)
Gilles Plante
Full Member
***
Offline


Posts: 156
Location: Québec, Canada
Joined: Oct 31st, 2013
Code completion and itellisense
Oct 31st, 2013 at 4:57pm
Print Post  
Hi all,

I am evaluating VM plugin in Atmel Studio 6.1 and code completition and intellisense do not work. I was under impression that it would work in Atmel Studio also (compared to Visual Studio).

Is there a couple of parameters that would be incorrectly set - the are zillions of them   Huh ?

Thanks

Gilles Plante
  
Back to top
 
IP Logged
 
Tim@Visual Micro
Administrator
*****
Offline


Posts: 12163
Location: United Kingdom
Joined: Apr 10th, 2010
Re: Code completion and itellisense
Reply #1 - Oct 31st, 2013 at 6:19pm
Print Post  
Hi,

Yes you are right intellisense and code completion should work in .pde and .ino source code. 

The Visual Micro installer is responsible for setting the registry keys to ensure this happens. Please run the un-install of Visual Micro and then run the install again.

When you uninstall and reinstall Visual Micro your personal settings will not be lost. You can uninstall via the installer or via Control Panel>Add or Remove Programs>Visual Micro

That usually fixes the problem if not then I can give you another solution.

Thanks
  
Back to top
WWWFacebookTwitterYouTube  
IP Logged
 
Gilles Plante
Full Member
***
Offline


Posts: 156
Location: Québec, Canada
Joined: Oct 31st, 2013
Re: Code completion and itellisense
Reply #2 - Nov 1st, 2013 at 1:51pm
Print Post  
Hi Tim,

I did unistall and reinstalled and now it works fine  Smiley. Some explanations about the whole process. Before I installed Atmel Studio, I had downloaded the plugin from your site. I the installed Atmel Studio and upon the initial run, I was suggested to have a look at the plugins. Since I found in the list Visual Micro, I installed it from within Atmel Studio. That was version 1.1309.11.

I uninstalled from the Control Pannel, but reinstalled from the .MSI I had downloaded. Same version 1.1309.11.

Could it make a diffrecence whether the plugin is installed from within Atmel Studio or from outside (Atmel Studio not running) ?

Thanks
  
Back to top
 
IP Logged
 
Tim@Visual Micro
Administrator
*****
Offline


Posts: 12163
Location: United Kingdom
Joined: Apr 10th, 2010
Re: Code completion and itellisense
Reply #3 - Nov 1st, 2013 at 2:27pm
Print Post  
Hi thanks for the feed back. No it doesn't make any difference however I suspect that either the first time atmel is run after install or the next it replenishes the settings and dumps the Vm changes.

I'm not really sure but we will nail it asap!
  
Back to top
WWWFacebookTwitterYouTube  
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

VS Arduino » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.