Dec 25th, 2024 at 2:06am (UTC)
 
 

Before logging an issue, please update to the latest release of Visual Micro from the Downloads Page.

When Logging a Support Issue in the Forum, please ensure you have also:-

  • Enabled vMicro > Compiler > Show Build Properties
  • Re-Compile your program with these settings enabled
  		Save the new Output to a Text File and....
  • Click the Reply button and attach as .txt file OR
  • Click here to Email us with the file attached, and a link to your post
Support requests without the output above may be impossible to answer, so please help us to help you
 
  VS Arduino › Visual Micro › Ideas, Suggestions and Related Tools › Auto re-connect serial monitor after upload fail
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Auto re-connect serial monitor after upload fail (Read 995 times)
Acuario
Full Member
***
Offline


Posts: 238
Location: Spain
Joined: Aug 28th, 2015
Auto re-connect serial monitor after upload fail
Dec 17th, 2023 at 6:12am
Print Post  
Hi,

During an upload via the serial port the serial port is disconnected. When the upload successfully completes it is automatically reconnected.

However if an upload via serial fails the serial port does not reconnect to the device.

This means I have to manually reconnect (push the Connect button) which is a pain...

Can it function the same way as when an upload is successful, i.e. automatically re-connect?

This is not the same as the Auto-Recon button which is related to the hardware being plugged in.
  
Back to top
 
IP Logged
 
Simon@Visual Micro
Administrator
*****
Offline


Posts: 2505
Joined: Feb 13th, 2019
Re: Auto re-connect serial monitor after upload fail
Reply #1 - Dec 18th, 2023 at 3:37pm
Print Post  
Thanks for the report.

Currently the software does not Auto-Open the Serial Monitor when the upload fails as it could be the failed upload means it will not be able to connect to the board (depending on where the upload process has failed).

Is the issue that you are using multiple COM Ports (e.g. one for upload, and one for the Serial Monitor) so the upload can fail if the Serial Port selected is only for Serial Output?

If you can give more detail around this we can consider it for development if there is not an alternative workaround available.

  
Back to top
WWWFacebookTwitterYouTube  
IP Logged
 
Acuario
Full Member
***
Offline


Posts: 238
Location: Spain
Joined: Aug 28th, 2015
Re: Auto re-connect serial monitor after upload fail
Reply #2 - Dec 18th, 2023 at 4:28pm
Print Post  
Hi, no just using a single port. I know if there is a problem on the port it doesn´t reconnect and this is ok. The annoyance is that the port is ok but the upload didn´t happen correctly so it doesn´t even try..

An example, using an Arduino mini with only RX, TX and ground. I do an upload but 
don´t press the reset button in time so the upload fails. My fault. But then I have to manually reconnect even if I do another upload that is successful. Nothing wrong with the port, just the operator..me.
  
Back to top
 
IP Logged
 
Tim@Visual Micro
Administrator
*****
Offline


Posts: 12166
Location: United Kingdom
Joined: Apr 10th, 2010
Re: Auto re-connect serial monitor after upload fail
Reply #3 - Dec 18th, 2023 at 4:41pm
Print Post  
Have you enabled auto reconnect on the serial monitor status bar?
  
Back to top
WWWFacebookTwitterYouTube  
IP Logged
 
Acuario
Full Member
***
Offline


Posts: 238
Location: Spain
Joined: Aug 28th, 2015
Re: Auto re-connect serial monitor after upload fail
Reply #4 - Dec 18th, 2023 at 6:09pm
Print Post  
Yes. Auto reconnect works if I physically unplug a device then plug it back in. It doesn´t affect reconnect on an upload failure.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

VS Arduino » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.